Successfully pass the free certification exam at IW Academy and become an Infinet Certified Engineer.
All outdoor devices are equipped with indoor power supply units. Exact type of IDU, which is used with each device model is specified in different models description (see below).
Indoor AC/DC injector with integrated lighting protection IDU-CPE
IDU-CPE is an indoor AC/DC PoE injector. It is designed only for R5000-Smn, R5000-Lmn and synchronization hub AUX-ODU-SYNC and has integrated lighting protection.
Parameter | Description | |
---|---|---|
Input voltage (AC) | 100 ... 240 V | |
Output voltage | + 48 V, 0.5 A | |
Power consumption | 24 W | |
Ethernet mode | 10/100 Mbps | |
Connectors and Interfaces |
| |
Ethernet Connectors Pin-out |
| |
Size and weight | 87x78x36,5 (LxWxH), 0.15 kg | |
Operating temperature | 0 °С ... +40 °С | |
Lightning protection |
|
Indoor AC/DC injector with integrated lighting protection IDU-BS-G
Indoor Gigabit PoE Injector with lightning protection for InfiLINK 2x2 and InfiMAN 2x2 family (except R5000-Qmxb).
Parameter | Description | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Size and weight | 125*72*38 mm (L*W*H), 0.3 kg | |||||||||
Connectors and Interfaces |
| |||||||||
Supported Ethernet Modes | 10/100/1000Mbps (Gigabit Ethernet pass-through) | |||||||||
Output Voltage & Current | +56 V, 0.9 A (50.4W Max) | |||||||||
Operating temperature range | 0 °С ... +40 °С | |||||||||
Ethernet Connectors Pin-out | ETH IN | Pin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
Description | A+ | A- | B+ | C+ | C- | B- | D+ | D- | ||
ETH OUT | Pin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | |
Description | A+ | A- | B+ | +VDC / C+ | +VDC / C- | B- | -VDC / D+ | -VDC / D- | ||
EMC | Meet:
| |||||||||
Lightning Protection | In compliance with:
|
Indoor AC/DC injector with integrated lighting protection IDU-BS-G(60W)
IDU-BS-G(60W) is an indoor AC/DC PoE injector with built-in lightning protection. PoE injector is powered by an AC supply in the 100-240 V range.
Parameter | Description |
---|---|
Compatible models | InfiLINK XG, InfiLINK XG 1000, InfiLINK 2x2 PRO, InfiMAN 2x2 BS, Quanta 70, Quanta 5, Quanta 6, InfiMAN Evolution BS |
Size | 151*62*38 mm (L*W*H) |
Weight | 0.32 kg |
Connectors and Interfaces |
|
Supported Ethernet Modes |
|
Input Voltage |
|
Output Voltage & Current |
|
Consumption |
|
Operating temperature range |
|
Pin Assignment and Polarity |
|
EMC | Meet:
|
Lightning Protection | In compliance with:
|
Indoor AC/DC injector IDU-CPE-G(24W)
IDU-CPE-G(24W) is an indoor Gigabit PoE injector which supports 100-240 V input range from the AC mains. IDU-CPE-G(24W) feeds 48 VDC power to the device by injecting it to the CAT5 Ethernet cable.
Parameter | Description | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Compatible models | Quanta 5, Quanta 6, Quanta 70, InfiLINK XG, InfiLINK 2x2 LITE, InfiMAN 2x2 STE, InfiMAN Evolution (except E5-BSQ), InfiLINK Evolution, AUX-ODU-SYNC | |||||||||
Size and weight | 97*53.5*33.5 mm, 0.133 kg | |||||||||
Connectors and Interfaces |
| |||||||||
Supported Ethernet Modes |
| |||||||||
Standards |
| |||||||||
Input Power Requirements |
| |||||||||
Consumption |
| |||||||||
Operating temperature range |
| |||||||||
Operating humidity |
| |||||||||
Storage temperature |
| |||||||||
Output Power Voltage |
| |||||||||
Ethernet Connectors Pin-out | LAN | Pin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
Description | A+ | A- | B+ | C+ | C- | B- | D+ | D- | ||
POE | Pin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | |
Description | A+ | A- | B+ | +VDC / C+ | +VDC / C- | B- | -VDC / D+ | -VDC / D- | ||
Safety |
|
Indoor DC/DC injector with integrated lightning protection IDU-CPE-DC
IDU-CPE-DC is an indoor DC/DC injector. It greatly reduces complexity of the deployment in the cases where DC source is available thus reducing both capital expenditures and total cost of ownership. It is desinged for all CPE units (Smn and Lmn) and has integrated lightning protection. The source of DC power supply can be +48 V or even -48 V, hence installation of CPE units is possible where other DC or AC power sources are unavailable.
Parameter | Description |
---|---|
Compatible models | R5000-Smn and R5000-Lmn |
Connectors and Interfaces |
|
Supported Ethernet Modes |
|
Input voltage |
|
Output voltage |
|
Power consumption |
|
Ethernet Connectors Pinout |
|
Lightning |
|
EMC | FCC Class B , EN55022 Class B, EN60945, EN50155 |
Safety | UL1950, CSA 22.2 & TUV EN60950 |
Size and Weight | 85x57x36 mm, 0.15 kg |
Indoor DC/DC injector with integrated lightning protection IDU-LA-G(V.01)
IDU-LA-G(V.01) is an indoor DC/DC injector. It greatly reduces complexity of the deployment in the cases where DC source is available thus reducing both capital expenditures and total cost of ownership.
IDU-LA-G(V.01) may be used for the following purposes:
- To serve as a line protection unit for indoor network equipment connected to the second Ethernet port on ODU.
- To connect third-party DC power sources to ODU (for example, to power the unit from solar power or wind power sources).
Technical parameters
Parameter | Description |
---|---|
Compatible models | InfiLINK XG, InfiLINK XG 1000, InfiLINK 2x2, InfiMAN 2x2, Quanta 5, Quanta 6, Quanta 70, InfiLINK Evolution, InfiMAN Evolution |
Output Voltage | The same as input |
Supported Ethernet Modes | 10/100/1000 Mbps (Gigabit Ethernet pass-through) |
Pin assignment and polarity | 1/2 (+), 3/6 (-), 4/5 (+), 7/8 (-) |
DC Range | Acceptable input DC range depends on the specific ODU model: • InfiLINK XG, InfiLINK XG 1000, InfiLINK 2x2 PRO, InfiMAN 2x2 BS, Quanta 70, Quanta 5, Quanta 6, InfiLINK Evolution, InfiMAN Evolution models: ±43... ±56 VDC • InfiLINK 2x2 Lite, InfiMAN 2x2 STE models: +9... +56 VDC (positive voltage only) |
Size and Weight | 115×65×40 mm, 0.15 kg |
Operating temperature range | from 0°С to +40°С |
CAUTION
Exposing unit to the unsupported voltage will result in irreparable damage to the unit! Always observe power requirements!
Connectors description
Mounting holes sizes
IDU-LA-G(V.01) Packing List
Cable assembly
Outdoor DC/DC injector with lightning protection AUX-ODU-INJ-G
Optional indoor/outdoor DC injector with built-in lightning protection. It greatly reduces complexity of the deployment in the cases where DC source is available on the rooftop eliminating the need of weather-sealed cabinets. AUX-ODU-INJ-G is compatible with all Infinet Wireless devices.
Parameter | Description | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
Size and Weight | 34x94x121 mm, 0.28 kg | |||||||||
Connectors and Interfaces |
| |||||||||
Supported Ethernet Modes |
| |||||||||
Water and Dust Protection |
| |||||||||
Operating temperature range |
| |||||||||
DC Range |
| |||||||||
CAUTION Using inappropriate DC source will damage the ODU, which will be not covered by warranty | ||||||||||
Ethernet Connectors Pin-out | ETH IN | Pin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
Description | Data pair A+ | Data pair A- | Data pair B+ | Data pair C- | Data pair C+ | Data pair B- | Data pair D+ | Data pair D- | ||
ETH OUT | Pin | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | |
Description | Data pair A+ | Data pair A- | Data pair B+ | +VDC + Data pair C- | +VDC + Data pair C+ | Data pair B- | -VDC + Data pair D+ | -VDC + Data pair D- | ||
Lightning Protection | In compliance with:
|
Packing List
AUX-ODU-INJ-G is supplied with a worm clamp TORRO 40-60/9 C7 W4 DIN 3017 - 2 pcs. The clamp is made of stainless steel A4, width 9 mm, allows the installation on a mast with a diameter of 35 to 60 mm. In case of mast diameter more than 60 mm, a similar clamps (up to a 230 mm diameter) with a width of up to 12-13 mm can be used.