| Parameter | Description |
|---|
| user [Login] | Assigns a name under which the system administrator enters the router from the console or remotely, using telnet/http. |
| password [Password] | Sets the system administrator's password. Use the "setpass" command to remove user name and password. |
[no]useAAA | Enables/disables device access control using a RADIUS server. To use the authentication the AAA module should be running (see "AAA (access control using RADIUS server)). Remember that the AAA authentication method has the highest priority and local login database is used only in case when the required account is not found on the RADIUS server. If there is no local user account the management interface will be accessible with any login and password even if the AAA authentication is turned on. |
| [no]useLocalAAA | Changes the authentication priority; the local account is checked first, in case it's not found, authentication is performed via RADIUS. |
| contact [String] | |
| guest [guest login] | Specifies a login for entering a guest mode, any password may be used. In the guest mode the router's configuration parameters neither security-related parameters can't be modified. Use the "system noguest" command to remove guest access. |
| name [System Name] | The device name that will be displayed in the browser tab title while the web interface is used. |
| prompt [any_word] | Replaces the prompt on the screen with the given word of a maximum length of 16 characters. |
| location [String] | Describes the system location; for example in SNMP protocol. |
| mgmtAccount [user:pass@host] | Access details for the software update server via SNMP. |
| gpsxy XX.XXXXX YY.YYYYY | Sets the geographical coordinates of the device (longitude, latitude). |
| log {on|off} | {show [offset] | clear}| [no]filter | {ADDR | -} | Manages the system log operation: - "on" – display messages on the current console.
- "off" – stop displaying messages on the console.
- "show" – show the system log (time is expressed in seconds/milliseconds back from the current time).
- "clear" – clear the system log.
- "[no]filter" – removes neighboring identical lines from system log leaving only one copy of each message and counts their recurrence (enabled by default).
- "ADDR" – IP address parameter specifies the UNIX host where the system log is located to which messages are directed under the standard "syslog" protocol. In the "syslogd" settings of the server set the "facility.level" equal to "user.notice" or just a numeric value 15 in order to registrate messages.
- "-" – disable logging on the remote host.
|
| factorypassword {single|otp} | Sets the access mode on the device with the factory password. Each unit has its unique factory access password that can be obtained via the technical support. Once obtained this password stays the same for each factory login attempt (the "single" mode). Setting the unit to "otp" mode tells it to ask for a new password each time the factory login is given (the unit will provide different sequences, that should be submitted to the technical support in order to obtain a new password). Whenever the unit is set to "single" mode again, its unique factory access password is restored. |
| search [seconds] | Forces all indication to blink for searching the devices in a group of one type units. By default, this mode turns off after 10 seconds. |
| [no]indicator | Enables/disables LED indicators on the unit in order to hide the active device. |
[no]fastroute | Enables/disables the fast routing mode. In this mode the router becomes invisible for traceroute network tracing procedures, while still performing all routing functions. It is not recommended to enable the fast routing mode simultaneously on several devices connected to the same cable Ethernet segment, because this may produce a IP packets storm. |
| [no]mintgateway | Позволяет использовать в качестве шлюза по умолчанию (default gateway) ближайший узел MINT, который сконфигурирован с опцией “mint extg”, если такой имеется. |
| [no]authFailLog | Enables/disables the unsuccessful authentication attempts logging. |
| [no]sendredirects | Enables/disables sending "icmp redirect" messages for the packets source suppression if routing is incorrectly configured. |
| [no]dropredirects | Enables/disables receiving "icmp redirect" messages for routing tables updating if routing is incorrectly configured. |
| OfficialAddress X.X.X.X | 0 | Sets the IP address which will be used as a source IP address in all outgoing connections of the unit. The "0" value removes the current address. |
| icmplimit N [200] | Sets the limit of the outcoming ICMP packets number per second (0 by default, no limitation applied). It helps to avoid the device reboot while network scanning programs are working. The "0" value removesall limitations. |
| uptime | Displays the time since the last system's reboot. |
| cpu | Indicates current CPU load (in percent). |
| [no]pager | Enables/disables page splits in the console output. |
| [no]ipforwarding | Enables/disables IP Forwarding. |
| info [-f] [NAME] | Displays device information: - "-f" – full information.
- "NAME" – information about specified section.
|
version | Displays the software version. |