...
Scrambling mode is not supported on InfiLINK Evolution / InfiMAN Evolution devices. Scrambling mode must be disabled on R5000 devices, otherwise the data corruption process will be observed in the wireless link.
The misoctl mode is not supported on InfiLINK Evolution / InfiMAN Evolution devices. The misoctl mode must be disabled on the R5000 devices, otherwise the data transmitted from the R5000 in the MISO mode will be processed incorrectly on the Evolution side. This may lead to incorrect radio parameter calculations.
Note |
---|
|
Please note misoctl mode is enabled by default on R5000 devices. To disable the mode, specify the following "rf rf5.0 -misoctl; conf saveweb". |
- Bitrate TX
- InfiLINK 2x2 / InfiMAN 2x2: 30000, 60000, 90000, 120000, 180000, 240000, 270000, 300000 (Kbps).
- InfiLINK Evolution / InfiMAN Evolution: 65000, 130000, 195000, 260000, 390000, 520000, 585000, 650000, 780000, 866700 (Kbps).
...
PoE-out mode is supported only on InfiLINK 2x2 LITE and InfiMAN 2x2 subscriber terminals.
The IDU-CPE-DC power supply can be used to power only the InfiLINK 2x2 LITE and InfiMAN 2x2 subscriber terminals.
To connect the AUX-ODU-SYNC device to wireless devices, specialized cables must be used:
...
Expand |
---|
title | Scenarios: R5000 - Master, InfiLINK Evolution - Slave |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Lmn сonfiguration | E-ST сonfiguration |
---|
Radio | Switching | Radio | Switching |
---|
- Type: Master.
- Frame Size: 5 ms.
- Channel width: 20 MHz.
- Frequency: 5800 MHz.
- Greenfield: disablemisoctl: disable
- Scrambling: disable
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#3: Data transmission
- Switch#100: Management in VLAN 100
| - Type:Slave.
- R5000 Compatibility mode: on
- Channel width: 20 MHz.
- Frequency: 5800 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#3: Data transmission
- Switch#100: Management in VLAN 100
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST link settings |
---|
|
|
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST switching settings |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST network settings |
---|
|
|
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Settings via the CLI R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: radio and switching settings |
---|
| rf rf6.0 band 20 transient
rf rf6.0 freq 5800 bitr max sid 10101010
mint rf6.0 -name "E5-STE1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5800 -sid 10101010 -type slave -autobitr -key "456123"
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.27/24
switch group 100 start
switch group 3 add 1 eth0 rf6.0
switch group 3 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03270 R5000-Lmn1 00043522CBE6 46/38 130/130 0/0 /TM/
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 8/7 (rx/tx), 15 (sum) Kbps
Total nodes in area: 2 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Save settings |
---|
| E5-STE1#1> сo sa |
|
Expand |
---|
title | Scenarios: R5000 - Slave, InfiLINK Evolution - Master |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Lmn configuration | E-ST configuration |
---|
Radio | Switching | Radio | Switching |
---|
- Type:Slave.
- Channel width: 40 MHz.
- Frequency: 5500 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#6: Data transmission
- Switch#150: Management in VLAN 150
| - Type: Master.
- R5000 Compatibility mode: on
- Frame Size: 5 ms.
- Channel width: 40 MHz.
- Frequency: 5500 MHz.
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#6: Data transmission
- Switch#150: Management in VLAN 150
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST link settings |
---|
|
|
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST switching settings |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST network settings |
---|
|
|
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Settings via the CLI R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: radio and switching settings |
---|
| rf rf6.0 band 40 transient
rf rf6.0 freq 5500 bitr max sid 10101011
mint rf6.0 -name "E5-STE2"
mint rf6.0 -type master
mint rf6.0 -key "123456"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi150 up
ifc vlan150 vlan 150 vlandev eth0 up
switch group 150 add 2 vlan150 rf6.0
svi 150 group 150
ifc svi100 192.168.98.28/24
switch group 150 start
switch group 6 add 1 eth0 rf6.0
switch group 6 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03270 R5000-Lmn1 00043522CBE6 46/38 130/130 0/0 /TM/
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 8/7 (rx/tx), 15 (sum) Kbps
Total nodes in area: 2 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Save settings |
---|
| E5-STE1#1> co sa |
|
...
Expand |
---|
title | Scenarios: E-BS - base station sector; R5000 and E-ST - subscriber terminals |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| E-BS configuration | R5000-Lmn configuration | E-ST configuration |
---|
Radio | Switching | Radio | Switching | Radio | Switching |
---|
- Type: Master.
- R5000 Compatibility mode: on
- Frame Size: 5 ms.
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном VLAN 10
- Switch#100: Management in VLAN 100
| - Type:Slave.
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Greenfield: disablemisoctl: disable
- Scrambling: disable
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном in VLAN 10
- Switch#100: Management in VLAN 100
| - Type:Slave.
- R5000 Compatibility mode: on
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном in VLAN 10
- Switch#100: Management in VLAN 100
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-BS settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-BS link settings |
---|
|
|
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-BS switching settings |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-BS network settings |
---|
|
|
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Note |
---|
| Perform the E-ST settings analog with E-BS. |
Settings via the CLI R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-BS settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Radio and switching settings |
---|
| rf rf6.0 band 40 transient
rf rf6.0 freq 5310 bitr max sid 10101010
mint rf6.0 -name "E5-BSE"
mint rf6.0 -type master
mint rf6.0 -key "456123"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.25/24
switch group 100 start
switch group 5 add 1 eth0 rf6.0
switch group 5 vlan 10
switch group 5 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Wireless connection statistics |
---|
| E5-BSE#1> mint map stat
==============================================================================
Interface rf6.0 TDM (5 ms DL/UL:Auto) (RSSI=-40 Dist=70)
Node 000435252611 "E5-BSE", Id 37425, Nid 0, (Master)
Freq 5310, Band 40, Sid 10101010, autoBitrate 400000/30000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03286 R5000-Lmn 00043522CBF6 47/42 300/300 0/0 /S/
37428 E5-STE2 000435152614 47/48 300/300 0/0 /S/
------- ---------------------------- ------------ ----- ------- ----- -------
2 active neighbors
Total load: 9/11 (rx/tx), 20 (sum) Kbps
Total nodes in area: 3
Links fault 2, Routes fault 0
# Optimal tdma distance 2 km |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Save settings |
---|
| E5-BSE#1> co sa |
Note |
---|
| Perform the E-ST settings analog with E-BS. |
|
Expand |
---|
title | Scenarios: R5000 - base station sector, R5000 and E-ST - subscriber terminals |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Mmx configuration | R5000-Lmn configuration | E-ST configuration |
---|
Radio | Switching | Radio | Switching | Radio | Switching |
---|
- Type: Master.
- Frame Size: 5 ms.
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
| - Type: Slave.
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
| - Type:Slave.
- R5000 Compatibility mode: on
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 20
|
|
|
Settings via the web interface R5000-Mmx, R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST link settings |
---|
|
|
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST switching settings |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title | E-ST network settings |
---|
|
|
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Settings via the CLI R5000-Mmx, R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: radio and switching settings |
---|
| rf rf6.0 band 20 transient
rf rf6.0 freq 5100 bitr max sid 10101011
mint rf6.0 -name "E5-STE_Slave1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5100 -sid 10101011 -type slave -autobitr -key "123456"
ifc svi200 up
ifc vlan200 vlan 200 vlandev eth0 up
switch group 200 add 2 vlan200 rf6.0
svi 200 group 200
ifc svi100 192.168.98.25/24
switch group 200 start
switch group 7 add 1 eth0 rf6.0
switch group 7 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE_Slave1", Id 37429, Nid 0, (Slave)
Freq 5100, Band 20, Sid 10101011, autoBitrate 156000/13000, Noise -103(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
13660 R5000-Mmx 00043514C93C 53/44 130/130 0/0 /TM/F
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 5/0 (rx/tx), 5 (sum) Kbps
Total nodes in area: 3 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Save settings |
---|
| E5-STE1#1> co sa |
|