Include Page |
---|
_Академия Инфинет | _Академия Инфинет | Hide_comments |
---|
...
Режим отображается вместе с префиксом команды в виде "RIP(режим)#". На рисунке ниже показана диаграмма переходов между режимами КО. Изначально КО находится Изначально КО находится в базовом режиме, который содержит набор команд только для просмотра текущего состояния маршрутизатора. Переход в режим конфигурации разрешен только для пользователя WANFlexпользователя системы, имеющего привилегии "super-user". После перехода в режим конфигурации выполняется его блокировка. Таким образом, вход в этот режим с другого терминала (например, другая сессия "telnet") будет невозможен. Для исключения "мертвой" блокировки КО автоматически выходит из режимов конфигурации, если в течение 2 минут не поступало никаких команд.
Center |
---|
scroll-title |
title | Рисунок - Диаграмма переходов между режимами КО |
---|
|
gliffydisplayName | RIP modes Copy |
---|
name | RIP modes Copy |
---|
pagePin | 1 |
---|
|
Команды могут иметь аргументы, которые указываются в различных форматах. Формат значения аргумента описывается в справке о наборе команд ("?") или в списке команд (параметр "help"). Ниже приведены возможные форматы:
...
Code Block |
---|
|
configure Configuration
access-list Add an access list entry
clear Reset functions
end End current mode and change to root mode (CTRL+C).
exit Back to WANFlex command shell (CTRL+D).
help Print command list
interface Select an interface to configure
authentication Authentication control
description Interface specific description
end End current mode and change to root mode (CTRL+C).
exit Back to WANFlex command shell (CTRL+D).
help Print command list
no Negate a command or set its defaults
receive Advertisement reception
send Advertisement transmission
show Show running system information
split-horizon Perform split horizon
key Authentication key management
no Negate a command or set its defaults
prefix-list Build a prefix list
route-map Create route-map or enter route-map command mode
end End current mode and change to root mode (CTRL+C).
exit Back to WANFlex command shell (CTRL+D).
help Print command list
match Match values from routing table
no Negate a command or set its defaults
on-match Exit policy on matches
route-map Create route-map or enter route-map command mode
set Set values in destination routing protocol
show Show running system information
router Enable RIP routing process
default-information Control distribution of default route
default-metric Set a metric of redistribute routes
distance Administrative distance
distribute-list Filter networks in routing updates
end End current mode and change to root mode (CTRL+C).
exit Back to WANFlex command shell (CTRL+D).
help Print command list
neighbor Specify a neighbor router
network Enable routing on an IP network
no Negate a command or set its defaults
offset-list Modify RIP metric
passive-interface Suppress routing updates on an interface
redistribute Redistribute information from another routing protocol
route RIP static route configuration
route-map Route map set
show Show running system information
tagged Tagged mode
timers Adjust routing timers
version Set routing protocol version
show Show running system information
stop stop
debug Set debugging print level
end End current mode and change to root mode (CTRL+C).
exit Back to WANFlex command shell (CTRL+D).
help Print command list
no Negate a command or set its defaults
show Show running system information
access-list List IP access lists
memory Memory statistics
prefix-list Build a prefix list
rip IP routing protocol process parameters and statistics
route Show RIP routes
running-config running configuration
thread Thread information
version Displays version |
...