Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Note
titleNOTE

 Before making the configurations in the "Network Settings" section, please read the information presented in the "MAC Switch" section.

Center

Image RemovedImage Added

For the following layer 2 and 3 logical interfaces, you are allowed to add (by clicking the corresponding buttons and specifying the interface number), remove and change the parameters of the interface:

...

Center
Scroll Title
titleTable - Network Settings

Scroll Table Layout
widths20%, 80%

Interface typeOperations
ethX
  • Configure the IP address(es) and the mask of the interface
  • The IP address(es) of the "ethX" interface is accessible via Ethernet LAN segment only (it won't be accessible via the "rfX"  interface from other neighbor unit)
  • The IP address(es) of the "ethX" interface is used in the routing process
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • DHCP option is disabled by default
  • Set the interface description (up to 72 characters)
  • Set the interface mode (for example: 1000BaseTX-fullduplex) - the default value is “Auto” (recommended)
  • Activate/deactivate PoE: this option is available only for eth1 interface of the units with two Fast Ethernet ports; it is used to ease the CCTV setup or to power up another InfiNet Infinet Wireless unit (except Omx, Mmx, Um and XmSmn or Lmn) - by default, it is deactivated
rfX
  • Configure the IP address(es) and the mask of the interface
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • DHCP option is disabled by default
  • Set the interface description (up to 72 characters)
sviX
  • SVI interface is a logical L3 interface of the switch (solely used for the management of the unit)
  • Configure the IP address(es) and the mask of the interface (as the management IP address(es) of the unit)
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically (as the management IP address(es) of the unit)
    • DHCP option is disabled by default
  • Set the interface description (up to 72 characters)
  • Remove the interface
  • Set the Switch group number which this interface is assigned to (bind the SVI interface to a switch group)
prfX
  • PRF interface makes the Ethernet interface that it is assigned to, to appear as a regular RF interface in terms of the MINT network (for more information please refer to the WANFleX OS User Manual)
  • Configure the IP address(es) and the mask of the interface
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • Set the interface description (up to 72 characters)
  • Remove the interface
  • Set the parent interface to be transmitted the encapsulated packets (assign the PRF interface to the physical Ethernet interface)
  • Set the channel number (from 0 to 3) on which the frames are sent and received by the parent interface
  • Both PRF interfaces (of the two units in the link) must have the same channel assigned in order to establish the wireless link
vlanX
  • Configure the IP address(es) and the mask of the interface in case you use this interface for the management of the unit, only (not recommended way)
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • Set the interface description (up to 72 characters)
  • Remove the interface
  • Set the parent interface to be transmitted the encapsulated packets
  • Configure the VLAN tag (or VLAN ID) for the current interface (from 1 to 4094)Enable/disable Q in Q
  • Select the VLAN mode: 802.1q, 802.1ad (QinQ), 802.1ah (Provider Backbone Bridges).
lagX
  • Link aggregation interface is a logical interface used to combine multiple physical channels into one logical channel in order to increase link capacity and redundancy (for the units with two physical Ethernet ports)
  • Configure the IP address(es) and the mask of the interface
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • Set the interface description (up to 72 characters)
  • Remove the interface
  • Set the parent interface to be aggregated the encapsulated packets
  • Enable/disable Fast Mode, which allows to react faster to changing air conditions
tunX
  • Configure the IP address(es) and the mask of the interface
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • Set the interface description (up to 72 characters)
  • Remove the interface
  • Set the tunneling mode: IPIP or GRE
tapX
  • Configure the IP address(es) and the mask of the interface
  • Enable/disable the interface
  • Enable/disable DHCP - obtain an IP address automatically
  • Set the interface description (up to 72 characters)
  • Remove the interface

Click the «Create Pseudo-RFPRF», «Create VLANCreate VLAN», «Create LAGCreate LAG» and «Create SVICreate SVI» buttons in order to create the corresponding interfaces in the unit configuration.

...