View Source

Introduction

To increase the wireless network throughput built on InfiLINK 2x2 / InfiMAN 2x2 families devices (R5000 series) the network can be partially or completely upgraded to the InfiLINK Evolution / InfiMAN Evolution families (Evolution series). Datasheets on these families are presented on the Infinet's website:

The document contains recommendations how to upgrade the wireless network from the R5000 series to Evolution and limitations that must be taken into account when R5000 and Evolution devices operate together in one network.

InfiLINK Evolution / InfiMAN Evolution advantages

InLINK Evolution / InfiMAN Evolution key features compared to InfiLINK 2x2 / InfiMAN 2x2:

Evolution devices operate in 4.9–6.4 GHz frequency bands, which allows to use the same devices in the 5 and 6 GHz bands.
Instant DFS technology support on firmware level. Evolution devices continuously perform background spectrum monitoring and seamlessly change channel to the least noisy frequency without link interruption, taking into account the spectrum conditions at the location of all connected devices.
The ability to operate in the 80 MHz band increases the Evolution devices performance twice compared to R5000. Infinet devices peformance data is shown in article "Performance of the Infinet Wireless devices".
All Evolution devices support the QAM256 5/6 modulation-code scheme allowing to get a performance advantage of up to 30% compared to the R5000.
10 modulation-code schemes allow to adapt to the radio deterioration by performance reduction with a small steps.
The spectrum allocated to the link is used by the InfiLINK Evolution family with maximum performance due to the spectral efficiency of 8.375 bit/s/Hz.
InfiMAN Evolution base station sector could be integrated into existing optical networks thanks to second SFP port.

InfiLINK Evolution / InfiMAN Evolution and InfiLINK 2x2 / InfiMAN 2x2 technical parameters comparison is given in the table below:

Parameter		InfiLINK 2x2 PRO	InfiLINK 2x2 LITE	InfiLINK Evolution	InfiMAN 2x2		InfiMAN Evolution
		InfiLINK 2x2 PRO	InfiLINK 2x2 LITE	InfiLINK Evolution	Base station	Subscriber Terminal	Base station	Subscriber Terminal
Frequency range, MHz		5 GHz: 4900–6050 6 GHz: 6050–6425	5 GHz: 4900–6050 6 GHz: 6050–6425	5 GHz: 4900–6050 5+6 GHz: 4900–6425	5 GHz: 4900–6050 6 GHz: 6050–6425	5 GHz: 4900–6050 6 GHz: 6050–6425	5 GHz: 4900–6050 6 GHz: 6050–6425	5 GHz: 4900–6050 5+6 GHz: 4900–6425
Channel width, MHz		5, 10, 20, 40	5, 10, 20, 40	5, 10, 20, 40, 80	5, 10, 20, 40		5, 10, 20, 40, 80
Transmit power, dBm		5 GHz: up to 27 6 GHz: up to 23	5 GHz: up to 25 6 GHz: up to 23	5 GHz: up to 25 5+6 GHz: up to 25	5 GHz: up to 27 6 GHz: up to 23	5 GHz: up to 25 6 GHz: up to 23	5 GHz: up to 27 6 GHz: up to 25	5 GHz: up to 25 5+6 GHz: up to 25
Modulation coding schemes		up to QAM64 5/6	up to QAM64 5/6	up to QAM256 5/6	up to QAM64 5/6		up to QAM256 5/6
Throughput, Mbps	40 MHz	up to 280	up to 180	up to 335	up to 250	up to 180	up to 360	up to 335
Throughput, Mbps	Max value	up to 280	up to 180	up to 670	up to 250	up to 180	up to 800	up to 670
Wired Interfaces		1xGE(RJ45)	1x Fast Ethernet 2x FastEthernet (PoE out)	1xGE(RJ45)	1xGE(RJ45)	1x Fast Ethernet 2x FastEthernet (PoE out)	1xGE(RJ45) 1xSFP 1xSYNC	1xGE(RJ45)
Proprietary technologies		Instant DFS (models with 2 radio modules)		Instant DFS	Instant DFS (models with 2 radio modules) Beamforming		Instant DFS Beamforming	Instant DFS
TDD sync		Via external synchronization hub			Via external synchronization hub		Via external synchronization hub
Multiple access method		CSMA-CA Polling TDMA	CSMA-CA Polling TDMA	TDMA	CSMA-CA Polling TDMA	CSMA-CA Polling TDMA	TDMA	TDMA
Consumption, W		20	15	15	20 35 (R5000-Qmxb)	15	30 35 (E5-BSQ)	15
Power options		90-240 VAC ~ 50/60 Hz ±43..56 VDC Proprietary PoE	90-240 VAC ~ 50/60 Hz +9..56 VDC Proprietary PoE	90-240 VAC ~ 50/60 Hz ±43..56 VDC Proprietary PoE or 802.3at	90-240 VAC ~ 50/60 Hz ±43..56 VDC Proprietary PoE	90-240 VAC ~ 50/60 Hz +9..56 VDC Proprietary PoE	90-240 VAC ~ 50/60 Hz ±43..56 VDC Proprietary PoE or 802.3at	90-240 VAC ~ 50/60 Hz ±43..56 VDC Proprietary PoE or 802.3at

*-Roadmap item.

Limitations

Limitations in device configuration and design must be taken into account during the network upgrade from R5000 series to Evolution, and R5000 with Evolution devices joint operation in one network.

InfiLINK Evolution / InfiMAN Evolution devices in the “transient” mode are guaranteed to work only with devices based on the H08 and H11 platforms of InfiLINK 2x2 and InfiMAN 2x2 families devices. Work with devices based on other platforms, for example, H05, H06 and H07 is not guaranteed.

Configuration Settings

Firmware version

The Evolution series devices support time division multiple access technology (TDMA). The devices are delivered only with TDMA firmware. Thus, the R5000 devices must be upgraded to the TDMA firmware version. Procedure how to upgrade the network from Polling firmware to TDMA are provided in the section "Upgrade from Polling to TDMA".

Channel width

The 80 MHz channel width is not supported on InfiLINK 2x2 / InfiMAN 2x2 devices.

Duplex modes

The 1000BaseTX-fullduplex, 1000BaseTX-fullduplex manual duplex modes are not supported on the InfiLINK 2x2 LITE / InfiMAN 2x2 subscriber terminal devices.

Greenfield mode

Greenfield mode is not supported on InfiLINK Evolution / InfiMAN Evolution devices. The Greenfield mode should be disabled on the R5000, as it leads to frame incompatibility at the header level.

It should be noted that Greenfield mode disabling on R5000 devices will reduce the performance on 10-15 %. This is due to the algorithm disabling that optimizing frames transmitted via a wireless link.

Scrambling mode

Scrambling mode is not supported on InfiLINK Evolution / InfiMAN Evolution devices. Scrambling mode must be disabled on R5000 devices, otherwise the data corruption process will be observed in the wireless link.

Bitrate TX
- InfiLINK 2x2 / InfiMAN 2x2: 30000, 60000, 90000, 120000, 180000, 240000, 270000, 300000 (Kbps).
- InfiLINK Evolution / InfiMAN Evolution: 65000, 130000, 195000, 260000, 390000, 520000, 585000, 650000, 780000, 866700 (Kbps).

Physical connection

Wired Interfaces number
- InfiLINK 2x2 LITE / InfiMAN 2x2 subscriber terminals: 2х FastEthernet (RJ45).
- InfiLINK Evolution / InfiMAN Evolution subscriber terminal: 1xGE (RJ45).
PoE-out

PoE-out mode is supported only on InfiLINK 2x2 LITE and InfiMAN 2x2 subscriber terminals.

IDU-CPE-DC power supply

The IDU-CPE-DC power supply can be used to power only the InfiLINK 2x2 LITE and InfiMAN 2x2 subscriber terminals.

CAB-SYNC cable

To connect the AUX-ODU-SYNC device to wireless devices, specialized cables must be used:

- InfiMAN 2x2 base station / InfiLINK 2x2 PRO: CAB-SYNC cable.
- InfiMAN Evolution base station: CAB-SYNC-E cable.

CAB-SYNC and CAB-SYNC-E datasheets are presented on the Infinet company's website in the section "Accessories".

R5000 and Evolution models compliance

The table below provides recommendations for replacing the InfiLINK 2x2 / InfiMAN 2x2 models with the InfiLINK Evolution / InfiMAN Evolution.

PtP		PtMP
InfiLINK 2x2	InfiLINK Evolution	InfiMAN 2x2	InfiMAN Evolution
R5000-Mmx/5.300.2x500.2x23	E5-ST25 / E6-ST25	Base station
R5000-Mmx/5.300.2x500.2x26	E5-ST28 / E6-ST28	R5000-Qmxb/5.300.2x300.2x21	E5-BSQ
R5000-Mmx/5.300.2x500.2x28	E5-ST28 / E6-ST28	R5000-Mmxb/5.300.2x500.2x16	E5-BSI
R5000-Omx/5.300.2x500	E5-STE / E6-STE	R5000-Omxb/5.300.2x500	E5-BSE
R5000-Mmx/6.300.2x200.2x24	E6-ST25	R5000-Lmnb/5.300.2x500.2x16	E5-BSI
R5000-Mmx/6.300.2x200.2x27	E6-ST28	R5000-Lmnb/5.300.2x500	E5-BSE
R5000-Omx/6.300.2x200	E6-STE	R5000-Mmxb/6.300.2x200.2x16	E6-BSI
R5000-Smn/5.300.2x300.2x19	E5-ST23 / E6-ST25	R5000-Omxb/6.300.2x200	E6-BSE
R5000-Smn/5.300.2x300.2x23	E5-ST23 / E6-ST25	R5000-Smnb/6.300.2x200.2x16	E6-BSI
R5000-Smn/5.300.2x500.2x23	E5-ST25 / E6-ST25	R5000-Lmnb/6.300.2x200	E6-BSE
R5000-Smn/5.300.2x300.2x26	E5-ST25 / E6-ST25	Subscriber terminal
R5000-Smn/5.300.2x500.2x26	E5-ST28 / E6-ST28	R5000-Smnc/5.300.2x300.2x19	E5-ST23 / E6-ST25
R5000-Smn/5.300.2x300.2x28	E5-ST28 / E6-ST28	R5000-Smnc/5.300.2x300.2x23	E5-ST23 / E6-ST25
R5000-Smn/5.300.2x500.2x28	E5-ST28 / E6-ST28	R5000-Smnc/5.300.2x300.2x26	E5-ST25 / E6-ST25
R5000-Lmn/5.300.2x300	E5-STE / E6-STE	R5000-Smnc/5.300.2x300.2x28	E5-ST28 / E6-ST28
R5000-Lmn/5.300.2x500	E5-STE / E6-STE	R5000-Lmnc/5.300.2x300	E5-STE / E6-STE
R5000-Smn/6.300.2x200.2x19	E6-ST18	R5000-Smnc/6.300.2x200.2x19	E6-ST18
R5000-Smn/6.300.2x200.2x24	E6-ST25	R5000-Smnc/6.300.2x200.2x24	E6-ST25
R5000-Smn/6.300.2x200.2x27	E6-ST28	R5000-Smnc/6.300.2x200.2x27	E6-ST28
R5000-Lmn/6.300.2x200	E6-STE	R5000-Lmnc/6.300.2x200	E6-STE

Upgrade Scenarios

Point-to-Point topology

In order to minimize the network outage due to the devices replacement we recommend to replace the device first at one end of the wireless link and then at the other. To do this:

Configure the switching and radio parameters on the InfiLINK Evolution device that are equal to the replaced InfiLINK 2x2, except "Network SID" value.
Enable R5000 Compatibility mode.
Install the InfiLINK Evolution device next to the one being replaced. The directions of the antennas must match. Connect the device to the power supply network.
On the remote device, change the "Network SID" to the value set on InfiLINK Evolution.
The wireless link will have to be established between the InfiLINK Evolution and InfiLINK 2x2.
Check the antennas alignment. Instructions are provided in the section "Antenna alignment".

Example of upgrading a Point-to-Point network topology

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-19_18-2-35.png

R5000-Lmn сonfiguration		E-ST сonfiguration
Radio	Switching	Radio	Switching
Type: Master. Frame Size: 5 ms. Channel width: 20 MHz. Frequency: 5800 MHz. Greenfield: disable Scrambling: disable Network SID: 10101010. Security Key: 456123.	Switch#3: Data transmission Switch#100: Management in VLAN 100	Type:Slave. R5000 Compatibility mode: on Channel width: 20 MHz. Frequency: 5800 MHz. Network SID: 10101010. Security Key: 456123.	Switch#3: Data transmission Switch#100: Management in VLAN 100

Settings via the web interface

R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The rest radio parameters and switching settings remain unchanged.

E-ST settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu⁣".
Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-12-47.png

Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-10-13.png

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-9-20.png

Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-15-2.png

Settings via the CLI

R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The rest radio parameters and switching settings remain unchanged.

E-ST settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Configure the radio parameters and switching.

rf rf6.0 band 20 transient
rf rf6.0 freq 5800 bitr max sid 10101010
mint rf6.0 -name "E5-STE1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5800 -sid 10101010 -type slave -autobitr -key "456123"
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.27/24
switch group 100 start
switch group 3 add 1 eth0 rf6.0
switch group 3 start

Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".

E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0  TDS
Node  000435152615  "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)

 ------- ---------------------------- ------------ -----  ------- ----- -------
   Id         Name                        Node      SNR   Bitrate Retry Options
 ------------------------------------ ------------ rx/tx   rx/tx  rx/tx -------
   03270 R5000-Lmn1                   00043522CBE6 46/38  130/130  0/0  /TM/
 ------- ---------------------------- ------------ -----  ------- ----- -------
 1 active neighbors
 Total load: 8/7 (rx/tx), 15 (sum) Kbps
 Total nodes in area: 2

Step 4: Save configuration.

E5-STE1#1> сo sa

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_9-10-15.png

R5000-Lmn configuration		E-ST configuration
Radio	Switching	Radio	Switching
Type:Slave. Channel width: 40 MHz. Frequency: 5500 MHz. Greenfield: disable Scrambling: disable Network SID: 10101011. Security Key: 123456.	Switch#6: Data transmission Switch#150: Management in VLAN 150	Type: Master. R5000 Compatibility mode: on Frame Size: 5 ms. Channel width: 40 MHz. Frequency: 5500 MHz. Network SID: 10101011. Security Key: 123456.	Switch#6: Data transmission Switch#150: Management in VLAN 150

Settings via the web interface

R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The rest radio parameters and switching settings remain unchanged.

E-ST settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu⁣".
Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-24-7.png

Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-28-51.png

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-27-49.png

Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-25-56.png

Settings via the CLI

R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The radio parameters and switching settings remain unchanged.

E-ST settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Configure the radio parameters and switching.

rf rf6.0 band 40 transient
rf rf6.0 freq 5500 bitr max sid 10101011
mint rf6.0 -name "E5-STE2"
mint rf6.0 -type master
mint rf6.0 -key "123456"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi150 up
ifc vlan150 vlan 150 vlandev eth0 up
switch group 150 add 2 vlan150 rf6.0
svi 150 group 150
ifc svi100 192.168.98.28/24
switch group 150 start
switch group 6 add 1 eth0 rf6.0
switch group 6 start

Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".

E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0  TDS
Node  000435152615  "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)

 ------- ---------------------------- ------------ -----  ------- ----- -------
   Id         Name                        Node      SNR   Bitrate Retry Options
 ------------------------------------ ------------ rx/tx   rx/tx  rx/tx -------
   03270 R5000-Lmn1                   00043522CBE6 46/38  130/130  0/0  /TM/
 ------- ---------------------------- ------------ -----  ------- ----- -------
 1 active neighbors
 Total load: 8/7 (rx/tx), 15 (sum) Kbps
 Total nodes in area: 2

Step 4: Save configuration.

E5-STE1#1> co sa

Point-to-Multipoint topology

To increase the network throughput, we recommend:

Replace the base station sector in accordance with the recommendations of the table in the section "R5000 and Evolution models compliance".
Replace critical subscriber terminals.

Example of upgrading a Point-to-Multipoint network topology

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_9-29-36.png

E-BS configuration		R5000-Lmn configuration		E-ST configuration
Radio	Switching	Radio	Switching	Radio	Switching
Type: Master. R5000 Compatibility mode: on Frame Size: 5 ms. Channel width: 40 MHz. Frequency: 5310 MHz. Network SID: 10101010. Security Key: 456123.	Switch#5: Data transmission в выделенном VLAN 10 Switch#100: Management in VLAN 100	Type:Slave. Channel width: 40 MHz. Frequency: 5310 MHz. Greenfield: disable Scrambling: disable Network SID: 10101010. Security Key: 456123.	Switch#5: Data transmission in VLAN 10 Switch#100: Management in VLAN 100	Type:Slave. R5000 Compatibility mode: on Channel width: 40 MHz. Frequency: 5310 MHz. Network SID: 10101010. Security Key: 456123.	Switch#5: Data transmission in VLAN 10 Switch#100: Management in VLAN 100

Settings via the web interface

R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
The radio parameters and switching settings remain unchanged.

E-BS settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu⁣".
Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-34-30.png

Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-38-49.png

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-39-20.png

Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-36-26.png

Perform the E-ST settings analog with E-BS.

Settings via the CLI

R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The radio parameters and switching settings remain unchanged.

E-BS settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Configure the radio parameters and switching.

rf rf6.0 band 40 transient
rf rf6.0 freq 5310 bitr max sid 10101010
mint rf6.0 -name "E5-BSE"
mint rf6.0 -type master
mint rf6.0 -key "456123"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5 
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.25/24
switch group 100 start
switch group 5 add 1 eth0 rf6.0
switch group 5 vlan 10
switch group 5 start

Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".

E5-BSE#1> mint map stat
==============================================================================
Interface rf6.0  TDM (5 ms DL/UL:Auto) (RSSI=-40 Dist=70)
Node  000435252611  "E5-BSE", Id 37425, Nid 0, (Master)
Freq 5310, Band 40, Sid 10101010, autoBitrate 400000/30000, Noise -100(+0)

 ------- ---------------------------- ------------ -----  ------- ----- -------
   Id         Name                        Node      SNR   Bitrate Retry Options
 ------------------------------------ ------------ rx/tx   rx/tx  rx/tx -------
   03286 R5000-Lmn                    00043522CBF6 47/42  300/300  0/0  /S/
   37428 E5-STE2                      000435152614 47/48  300/300  0/0  /S/
 ------- ---------------------------- ------------ -----  ------- ----- -------
 2 active neighbors
 Total load: 9/11 (rx/tx), 20 (sum) Kbps
 Total nodes in area: 3
 Links fault 2, Routes fault 0
 # Optimal tdma distance 2 km

Step 4: Save configuration.

E5-BSE#1> co sa

Perform the E-ST settings analog with E-BS.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_9-38-32.png

R5000-Mmx configuration		R5000-Lmn configuration		E-ST configuration
Radio	Switching	Radio	Switching	Radio	Switching
Type: Master. Frame Size: 5 ms. Channel width: 20 MHz. Frequency: 5100 MHz. Greenfield: disable Scrambling: disable Network SID: 10101011. Security Key: 123456.	Switch#7: Data transmission Switch#200: Management in VLAN 200	Type: Slave. Channel width: 20 MHz. Frequency: 5100 MHz. Greenfield: disable Scrambling: disable Network SID: 10101011. Security Key: 123456.	Switch#7: Data transmission Switch#200: Management in VLAN 200	Type:Slave. R5000 Compatibility mode: on Channel width: 20 MHz. Frequency: 5100 MHz. Network SID: 10101011. Security Key: 123456.	Switch#7: Data transmission Switch#200: Management in VLAN 20

Settings via the web interface

R5000-Mmx, R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The radio parameters and switching settings remain unchanged.

E-ST settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu⁣".
Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-44-31.png

Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-47-14.png

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-47-45.png

Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.

Infinet Wireless: Technical Documentation > Upgrade from R5000 to Evolution > image2021-8-20_10-45-30.png

Settings via the CLI

R5000-Mmx, R5000-Lmn settings

Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Check the parameters disabling:
- Greenfield
- Scrambling.
The radio parameters and switching settings remain unchanged.

E-ST settings

Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
Step 2: Configure the radio parameters and switching.

rf rf6.0 band 20 transient
rf rf6.0 freq 5100 bitr max sid 10101011
mint rf6.0 -name "E5-STE_Slave1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5100 -sid 10101011 -type slave -autobitr -key "123456"
ifc svi200 up
ifc vlan200 vlan 200 vlandev eth0 up
switch group 200 add 2 vlan200 rf6.0
svi 200 group 200
ifc svi100 192.168.98.25/24
switch group 200 start
switch group 7 add 1 eth0 rf6.0
switch group 7 start

Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".

E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0  TDS
Node  000435152615  "E5-STE_Slave1", Id 37429, Nid 0, (Slave)
Freq 5100, Band 20, Sid 10101011, autoBitrate 156000/13000, Noise -103(+0)

 ------- ---------------------------- ------------ -----  ------- ----- -------
   Id         Name                        Node      SNR   Bitrate Retry Options
 ------------------------------------ ------------ rx/tx   rx/tx  rx/tx -------
   13660 R5000-Mmx                    00043514C93C 53/44  130/130  0/0  /TM/F
 ------- ---------------------------- ------------ -----  ------- ----- -------
 1 active neighbors
 Total load: 5/0 (rx/tx), 5 (sum) Kbps
 Total nodes in area: 3

Step 4: Save configuration.

E5-STE1#1> co sa