InfiMONITOR NEXT allows the network engineers to monitor the status of the wireless devices and to manage their configurations.

Devices review

The section includes two key areas:

The list of devices is displayed in a table with the following columns:

To apply a device filter, use the "Add filter" button at the top of the list and set the search parameters. The "IP-address" filter allows to search both a single address and a range of addresses (no more than 255).


Device profile

Each device is presented by its profile contains the whole information about device. There are following section in profile:

The "Status" section consists of several parts:

There is special section includes both the current and remote device. This section presents characteristics of wireless link in downstream and upstream. For local and remote devices, there is the ability to switch to its web interface or to manage via the command line.

Network infrastructure requirements

Management functionality requires network connectivity from wireless devices to the monitoring system port 2121/TCP, please check your firewall rules.

Management

Management tools are presented in the "Maintenance" section of device's profile.

Configuration

The configuration is automatically loaded for each device added to InfiMONITOR NEXT. If the device's configuration has been changed, it will be reloaded, but the previous configuration won't be deleted. Thus, the monitoring system always stores both the current device configuration and its previous versions.

The configuration management feature is only available for devices that have been successfully provisioned. For more details proceed to the Description and operational principles section.

To update devices configurations safely via the monitoring system, perform a firmware update.

For InfiLINK 2x2, InfiMAN 2x2 families:

  • MINT firmware version - above 1.98.50;
  • TDMA firmware version - above 2.1.30.

For InfiLINK XG, InfiLINK XG 1000 families:

  • Firmware version 1.8.4.

There are no restrictions for the InfiLINK Evolution, InfiMAN Evolution, Quanta 5/6/70 families.

To view the device configurations list, click on the "Manage" button in the "Configuration" row:

The list of configurations includes the entire configuration history, displayed as a table with the following columns:

Select any configuration to view it:

You can compare the two configurations to see how they differ. To do this, in the "Compare" list, select any other configuration.

To highlight changes in the comparison mode, click on the "Show the difference" button.



Configuration changing

Changing the device's configuration includes the following steps:

  1. Select the configuration version.
  2. Edit selected configuration.
  3. Create job - set a task for applying the configuration on the device.
  4. Apply the configuration — the configuration is applied on the device.

Configuration editing

Click "Edit" button in the selected configuration. A draft will be created, with the content identical to the previously selected configuration. Each device may have only one configuration draft. If you create a new draft the previous will be rewritten.

After editing, you can save a draft without applying it on the device, or create a job to apply it. You may apply any configuration version without editing by clicking "Create job" button.

Job creation

When you are ready to apply configuration draft please click "Create job" button.

In the menu, you can schedule the time for applying the configuration, the following options are available:

In order to perform the jobs execution at a required time, it is necessary to set date and time on the virtual machine where InfiMONITOR NEXT is installed. Time settings can not be made in the monitoring system.

Applying the configuration

At the set time, the configuration will be downloaded to the device. After successful validation, the configuration will be applied and the device will reboot.

Configuration applying procedure eliminates the risk of loss of communication with the device due to configuration errors or other failures. For details, see the Description and operational principles.

After rebooting the device, InfiMONITOR NEXT will re-poll it and perform a configuration check. If it was applied correctly, then the job will be marked as completed successfully. Otherwise, the job will fail.

Firmware

The monitoring system provides the ability to update the software, both on one and on a group of devices.

Upload firmware files

To update the firmware, it must be previously uploaded into a special storage of the monitoring system. In order to do this, go to the "Management" section and click the "Firmware" button.

Each file in the repository has the following fields:

Firmware update

The firmware update is performed via a special update job. In order to do this, go to the "Maintenance" section of the device card. In the "Firmware" line click the "Manage" button. This will open a list of firmware files suitable for this device.

Select the firmware version to be applied to the device, then click the "Create job" button. Same to the configuration update jobs, you can run the update immediately or schedule it for a later time.

Devices groups

The devices can be joined in groups. Grouping is necessary to manage visibility areas and perform group operations such as software updates. Each device must be added to at least one group.

By default, InfiMONITOR NEXT has the following groups:

To manage groups in "Device Management" section, go to the "Device Groups" subsection.
This section provides a list of all groups created in the monitoring system, to create a new group, click the "Add Group" button on the sidebar. To view devices of a particular group, select the group and click the "Show devices in group" button on the sidebar.

Command execution

The monitoring system allows to manage the device using the command line. The command line is available in the "CLI" subsection of the device status section.

To clear the command line window, click theimage2023-9-6_11-15-6.pngbutton.

To manage the device from the monitoring system, it must be provisioned, see System configuration - Provisioning.

A complete list of commands is available in the technical documentation: