Wireless link throughput is lower than expected

Performance tests

Web interface

The throughput test can be performed with the "Performance Tests" tool built into the web interface in the section "Device status" → "Link statistics for the rf5.0 interface". This tool generate test traffic, it allows to obtain data about the real link throughput both in one direction and in a two-way manner. Throughput evaluation are made for traffic with the specified priority without taking into account the service traffic required to maintain the link operation. To exclude the influence of data traffic on the test result, it is recommended to set the highest priority for test traffic (at least 15). When the MINT testing mode is enabled (the "use MINT" checkbox), performance tests are always performed on the highest modulation, otherwise testing will be performed on each modulation available. The detailed parameters description and performance tests settings is available in the "Device Status menu" article.

Command line interface

When using the command line interface to manage the device, it is possible to test the radio link via the "ltest" command.

Wireless connection status

Link statistics on rf5.0 interface

Web interface

To evaluate the wireless connection quality with the neighboring device use the color indication in the "Status" column of the "Link statistics on rf5.0" subsection:

• Red: bad connection.
• Yellow: good connection.
• Green: perfect connection.

The following symbols indicate problems:

• At the wireless connection uptime column:

  • F - the local device has a newer software version than the remote.

  • E - the Ethernet port of the remote device is flapping.

• At the TX power column:
  • * - hardware device failure.
• At the RSSI column (only for software with TDMA technology support):
  • * - significant difference in the signals power of vertical and horizontal polarizations.

Make sure the "TX Power" and "Bitrate" parameters match the values of the planning phase. In the "Link statistics on rf5.0" of the "Device status" section, pay attention to the wireless connection parameters. The main parameters are the retries number and the bitrate. It is not recommended to use the link with the retries number exceeding 5%. The actual bitrate (modulation level) depends on the SNR parameter - the signal-to-noise ratio. The highest modulations are available at SNR values of 27-50 dB.

For detailed description of the link parameters proceed to the "Device Status menu" article.

Command line interface

To display information about the wireless links status via the command line interface, use the "mint rf5.0 map detail" command.

Pay attention to the indicators in the "Options" column, the following values are possible:

• M - Master device;
• S - Slave device;
• TM - Master device with software with TDMA technology support;
• P - polling mode is enabled;
• L - throughput is limited by license;
• F - the software version is older than on the local device.
  

A question mark in front of the remote device name indicates that it has no password.

Pay attention to the "*" symbol, which can represent the following:

• At the "pwr" column - hardware device failure.
• At the "rssi" column (only for software with TDMA technology support) - significant difference in the signals power of vertical and horizontal polarizations.

Radio statistics

Web interface

In case of a high retries level use the built-in statistics tools. "General statistics" section contains information about media loading, queue overflow, etc..

Figure - General statistics

Pay attention to the following indicators:

• "Lost Frames" the frames number that were not received by the device, even after retries.
• "Duplicates Received" the frames number that were received several times due to the other side did not receive an acknowledgment of the frame receipt.
• "Aggr Subframe Retries" and "Aggr Full Retries" the frames number that the device sent several times because the other side did not acknowledge receipt.
• "Exscessive Retries" the frames number failed to send after all retry attempts.

Command line interface

To display statistic via the command line interface, use the ""rfconfig stat" command.

QoS statistic

Web interface

The "QoS statistics" section provides information about transmitted and dropped packets in each priority queue configured on the device. Drops in traffic processing queues indicates that the throughput threshold has been exceeded. Losses in queue q00 (P16) are acceptable because this queue contains performance test data.

Command line interface

To display statistic via the command line interface, use the "rfconfig rf5.0 stat qos" command. The dropped packets number for each configured queue can be displayed by the "qm stat" command.

Statistics graphs

If the link has deteriorated during operation, with the initial parameters corresponding to the calculated ones, it is necessary to find out when the problem has begin. Use the "Statistics graphs" tool to determine when or how often the problem occurs by changing the display options.

Device status

Pay attention to the CPU and memory usage indicators in the "Device status" section. Excessive processes running on a device can overflow volatile memory and overload the CPU (over 95% usage), and deteriorate wireless link quality. The CPU load can be displayed with the "system cpu" command, and information about the device memory state by the "mem" command.

Last reboot reason

Disruptions in the wireless link may be caused by the device reboot. At the "Maintenance" section or at the "system uptime" command output pay attention to the last device reboot reason. Following values are possible:

• "Software fault".
• "Unexpected restart".
• "Manual restart".
• "Manual delayed restart".
• "Firmware upgrade".
• "SNMP managed restart".
• "Test firmware loaded".
• "Power-on reset".

System log

Proceed to the System Log tool in the "Device status" section or by using the "system log" command. Using the log entries, check if the link degradation was caused by a configuration change ("system reconfiguration" message). Restore the configuration previous version if necessary. Detailed information about saving and uploading configuration is available in the "General Purpose Command Set" article.

Pay attention to the following messages:

Частое изменение статуса Ethernet-интерфейса ("Up" и "Down") может свидетельствовать о проблемах интерфейса Ethernet, подключенного к нему кабеля, источника питания или коммутатора.

Юстировка антенны

Web-интерфейс

Деградация канала связи может быть вызвана нарушением юстировки или появлением препятствий на пути распространения сигнала. Воспользуйтесь встроенным инструментом "Юстировка антенны". Рекомендуемые параметры указаны в таблице ниже. Если параметры связи существенно отличаются от расчётных, проверьте точность юстировки устройств с обеих сторон канала связи.

Сохранение параметра RSSI на высоком уровне при снижении значений параметра CINR может свидетельствовать о помехе вблизи одного из устройств. Ухудшение параметров RSSI и CINR, может быть показателем нарушения юстировки устройств. Подробное описание работы инструмента "Юстировка антенны" доступно в соответствующем разделе статьи "Состояние устройства". 

Интерфейс командной строки

При использовании командной строки для управления устройством, точная юстировка антенны выполняется командой "ltest rf5.0 MAC ADDRESS -align". В выводе команды будет указано среднее значение CINR для локального и удалённого устройства.

Анализ состояния радиочастотной среды

Web-интерфейс

Для оценки состояния радиосреды обратитесь к инструменту "Radio Scanner". Инструмент имеет следующие назначения:

• позволяет оценить источники радиоизлучения на текущей центральной частоте и, при необходимости, выполнить частотное разнесение устройств с целью снижения их взаимного влияния;
• выводит информацию о импульсных помехах. Количество импульсов в секунду свыше 50 говорит о существенных помехах на выбранной частоте. 

Для выбора частоты свободной от помех используйте инструмент "Спектроанализатор", либо воспользуйтесь механизмами автоматического выбора частоты. Подробнее об алгоритмах динамического выбора рабочей частоты можно узнать в статье "Динамический выбор частоты".

Рисунок - Radio Scanner

Интерфейс командной строки

Более подробная информация о состоянии радиосреды доступна посредством команды "muffer". Так команда "muffer rf5.0 scan" позволяет выполнить глубокий анализ радиосреды на наличие источников радиосигналов на всех доступных частотах.