Successfully pass the free certification exam at IW Academy and become an Infinet Certified Engineer.
ifc radio
Use this command to enable or disable the system radio interface.
Syntax:
#1> ifc radio {up | down}
xg
Use this command to set the air link parameters.
Syntax:
#1> xg [arguments]
#1> xg usage: xg config xg config -peer-exported xg config -defaults xg [-grids-carrier-ix=<carrier-ix>] [-grids-band=<channel-width>] -grids {<freq_start>[-<freq_end>[/<step>]]}[,...] xg [-grids-carrier-ix=<carrier-ix>] [-grids-band=<channel-width>] -grids= General settings xg -type {master, slave} xg -tdd-sync-src {freerun, gnss} xg -autosync-link-settings {no, no-co-sa-no-reboot, no-reboot, reboot-remote-if-needed} Link shared settings (Radio Front End) xg -cell-id {0..15/1} xg -channel-width {10, 20, 40} (channel-width 10): xg -freq-dl {6005..6415/50} (channel-width 20): xg -freq-dl {6010..6410/20} (channel-width 40): xg -freq-dl {6020..6400/50} (channel-width 10): xg -freq-ul {6005..6415/50} (channel-width 20): xg -freq-ul {6010..6410/20} (channel-width 40): xg -freq-ul {6020..6400/50} xg -short-cp {0, 1} xg -freg-auto {0, 1} Link shared settings (Frame Config) xg -max-distance {1..100/1} xg -sframelen {2, 4, 5, 10} xg -tdd-profile {0..7/1} xg -tdd-profile-auto-switching {0, 1} RF per-station settings xg -txpwr {0..27/1} xg -ctrl-block-boost {0, 1} xg -atpc-master-enable {0, 1} xg -atpc-target-rssi {-70..-40/1} xg -atpc-rssi-threshold {0..5/1} Modulation related xg -amc-strategy {normal, conservative, aggressive} xg -max-mcs {1..11/1} DFS/RSSI scan/Radar detection xg -idfs-enable {0, 1} xg -idfs-rssi-threshold {1..50/1} xg -idfs-ffs-time {0..600/1} xg -idfs-rdrdt-enable {0, 1} xg -idfs-fix-dl-ul {0, 1} Ethernet datapath related xg -traffic-prioritization {off, on} Supplementary xg -config-restore-time {1..60/1} xg -config-restore-index {1..8/1} xg -passphrase=<pass> aliases: xg -freq <val> => xg -freq-dl <val> -freq-ul <val>
Commands and options description is given in the table below:
Command | Description |
---|---|
xg config |
|
xg config -peer-exported |
The outputs have the following view: xg -v3-start xg -v3 <encoded web config> xg -v3-end |
xg config -defaults |
|
xg [-grids-carrier-ix=<carrier-ix>] [-grids-band=<channel-width>] -grids {<freq_start>[-<freq_end>[/<step>]]}[,...] |
|
xg [-grids-carrier-ix=<carrier-ix>] [-grids-band=<channel-width>] -grids= |
|
xg -type {master | slave} |
Example, xg -type master |
xg -tdd-sync-src {freerun | gnss} |
CAUTION GNSS option is effective for "master" unit only. CAUTION Before enabling "gnss" option make sure that built-in GNSS-receiver is configured properly. Use "gps" command to configure or check the status (use values of "HDOP" up to 1.5). |
xg -autosync-link-settings {no, no-co-sa-no-reboot, no-reboot, reboot-remote-if-needed} | Automatic link synchronization:
The automatic link synchronization option will always be executed if it is enabled in CLI and not checked in the web interface |
xg -cell-id {0..15/1} |
Example, xg -cell-id 15 |
xg -channel-width {10, 20, 40} |
|
(channel-width 10): xg -freq-dl {6005..6415/50} (channel-width 20): xg -freq-dl {6010..6410/20} (channel-width 10): xg -freq-dl {6020..6400/50} |
Example, xg -freq-dl 6410 NOTE For the units with two radio modules the downlink center frequency must be set for both. Example, xg -freq-dl [0]6000,[1]6100 |
(channel-width 10): xg -freq-ul {6005..6415/50} (channel-width 20): xg -freq-ul {6010..6410/20} (channel-width 10): xg -freq-ul {6020..6400/50} |
Example, xg -freq-ul 6400 NOTE For the units with two radio modules the uplink center frequency must be set for both. Example, xg -freq-ul [0]6200,[1]6300 |
xg -short-cp {0, 1} |
|
xg -freg-auto {0, 1} |
Example, xg -freq 6415 |
xg -max-distance {1..100/1} |
Example, xg -max-distance 50 |
xg -sframelen {2, 4, 5, 10} |
Example, xg -sframelen 10 |
xg -tdd-profile {0..7/1} |
Example, xg -tdd-profile 5 DL/UL values for the profile 5: |
xg -tdd-profile-auto-switching {0, 1} |
|
xg -txpwr {0..27/1} |
NOTE For the units with two radio modules the transmit power must be set for both. The value range is 0…22 dBm in increments of 1 dBm. Example, xg -txpwr [0]10,[1]15 |
xg -ctrl-block-boost {0, 1} |
|
xg -atpc-master-enable {0, 1} |
|
xg -atpc-target-rssi {-70..-40/1} |
|
xg -atpc-rssi-threshold {0..5/1} |
|
xg -amc-strategy {normal, conservative, aggressive} |
|
xg -max-mcs {1..10/1} |
|
xg -idfs-enable {0, 1} |
|
xg -idfs-rssi-threshold {1..50/1} |
|
xg -idfs-ffs-time {0..600/1} |
|
xg -idfs-rdrdt-enable {0, 1} |
|
xg -idfs-fix-dl-ul {0, 1} |
|
xg -traffic-prioritization {0..1/1} |
|
xg -config-restore-time {1..60/1} |
NOTE Detailed description is given in the document "Safety apply settings in InfiLINK XG / InfiLINK XG 1000". |
xg -config-restore-index {1..8/1} |
|
xg -passphrase=<pass> |
|
xg -freq<val> => xg -freq-dl <val> -freq-ul <val> |
Example, xg -freq 6415 |
NOTE
Initial configuration procedure of the PtP link setup between the units is described in the section "Laboratory pre-configuration".
xginfo
Use this command to output the information data.
Syntax:
#1> xginfo [arguments]
#1> xginfo usage: xginfo stat [-verbose] [-clear] [-1] xginfo capabilities [-verbose] xginfo version xginfo availability
"xginfo" command arguments description is given in the table below
Command | Description |
---|---|
xginfo stat [-verbose] [-clear] [-1] |
|
xginfo capabilities [-verbose] |
|
xginfo version |
|
xginfo availability [-verbose] [-clear] |
|
xgutils
Syntax:
#1> xgutils [arguments]
#1> xgutils usage: xgutils ber-amc-show [-carrier <CARRIER_NUM>] [-1] xgutils ber-amc-reset [-mask <STREAM_MASK>]
"xgutils" commands and options description is given in the table below
Command | Description |
---|---|
xgutils ber-amc-show [-carrier <CARRIER_NUM>] [-1] |
|
xgutils ber-amc-reset [-mask <STREAM_MASK>] |
|
xgutils dfs -list [-clear] |
|
xgutils dfs -stat [-clear] |
|
xgdfs
Syntax:
#1> xgdfs [arguments]
#1> xgdfs usage: xgdfs -list [-clear] xgdfs -stat [-clear]
"xgdfs" commands and options description is given in the table below
Command | Description |
---|---|
xgdfs -list [-clear] |
|
xgdfs -stat [-clear] |
|