Introduction
...
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | InfiLINK Evolution / InfiMAN Evolution with InfiLINK 2x2 / InfiMAN 2x2 comparison |
---|
| Parameter | InfiLINK 2x2 PRO | InfiLINK 2x2 LITE | InfiLINK Evolution | InfiMAN 2x2 | InfiMAN Evolution |
---|
| Base station | Subscriber Terminal | Base station | Subscriber Terminal |
---|
Frequency range, MHz | - 5 GHz: 4900–6050
- 6 GHz: 6050–6425
| - 5 GHz: 4900–6050
- 6 GHz: 6050–6425
| - 5 GHz: 4900–6050
- 5+6 GHz: 4900–6425
| - 5 GHz: 4900–6050
- 6 GHz: 6050–6425
| - 5 GHz: 4900–6050
- 6 GHz: 6050–6425
| - 5 GHz: 4900–6050
- 6 GHz: 6050–6425
| - 5 GHz: 4900–6050
- 5+6 GHz: 4900–6425
|
---|
Channel width, MHz | | | | | |
---|
Transmit power, dBm | - 5 GHz: up to 27
- 6 GHz: up to 23
| - 5 GHz: up to 25
- 6 GHz: up to 23
| - 5 GHz: up to 25
- 5+6 GHz: up to 25
| - 5 GHz: up to 27
- 6 GHz: up to 23
| - 5 GHz: up to 25
- 6 GHz: up to 23
| - 5 GHz: up to 27
- 6 GHz: up to 25
| - 5 GHz: up to 25
- 5+6 GHz: up to 25
|
---|
Modulation coding schemes | | | | | |
---|
Throughput, Mbps
| 40 MHz | | | | | | | |
---|
Max value | | | | | | | |
---|
Wired Interfaces | | 1x Fast Ethernet - 2x FastEthernet (PoE out)
| | | 1x Fast Ethernet - 2x FastEthernet (PoE out)
| | |
---|
Proprietary technologies | - Instant DFS (models with 2 radio modules)
|
| | - Instant DFS (models with 2 radio modules)
- Beamforming
|
| | |
---|
TDD sync | |
|
| |
| |
|
---|
Multiple access method | | | | | | | |
---|
Consumption, W | | | | | | | |
---|
Power options | - 90-240 VAC ~
50/60 Hz - ±43..56 VDC
- Proprietary PoE
| - 90-240 VAC ~
50/60 Hz - +9..56 VDC
- Proprietary PoE
| - 90-240 VAC ~
50/60 Hz - ±43..56 VDC
- Proprietary PoE or 802.3at
| - 90-240 VAC ~
50/60 Hz - ±43..56 VDC
- Proprietary PoE
| - 90-240 VAC ~
50/60 Hz - +9..56 VDC
- Proprietary PoE
| - 90-240 VAC ~
50/60 Hz - ±43..56 VDC
- Proprietary PoE or 802.3at
| - 90-240 VAC ~
50/60 Hz - ±43..56 VDC
- Proprietary PoE or 802.3at
|
---|
|
|
Limitations
Limitations in device configuration and design must be taken into account during the network upgrade from R5000 series to Evolution, and R5000 with Evolution devices joint operation in one network.
Note |
---|
|
InfiLINK Evolution / InfiMAN Evolution devices in the “transient” mode are guaranteed to work only with devices based on the H08 and H11 platforms of InfiLINK 2x2 and InfiMAN 2x2 families devices. Work with devices based on other platforms, for example, H05, H06 and H07 is not guaranteed. |
Configuration Settings
...
Scrambling mode is not supported on InfiLINK Evolution / InfiMAN Evolution devices. Scrambling mode must be disabled on R5000 devices, otherwise the data corruption process will be observed in the wireless link.
The misoctl mode is not supported on InfiLINK Evolution / InfiMAN Evolution devices. The misoctl mode must be disabled on the R5000 devices, otherwise the data transmitted from the R5000 in the MISO mode will be processed incorrectly on the Evolution side. This may lead to incorrect radio parameter calculations.
- Bitrate TXInfiLINK 2x2 / InfiMAN 2x2Bitrate TX
- InfiLINK 2x2 / InfiMAN 2x2: 30000, 60000, 90000, 120000, 180000, 240000, 270000, 300000 (Kbps).
- InfiLINK Evolution / InfiMAN Evolution: 65000, 130000, 195000, 260000, 390000, 520000, 585000, 650000, 780000, 866700 (Kbps).
...
PoE-out mode is supported only on InfiLINK 2x2 LITE and InfiMAN 2x2 subscriber terminals.
The IDU-CPE-DC power supply can be used to power only the InfiLINK 2x2 LITE and InfiMAN 2x2 subscriber terminals.
To connect the AUX-ODU-SYNC device to wireless devices, specialized cables must be used:
...
Expand |
---|
title | Scenarios: R5000 - Master, InfiLINK Evolution - Slave |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Lmn сonfiguration | E-ST сonfiguration |
---|
Radio | Switching | Radio | Switching |
---|
- Type: Master.
- Frame Size: 5 ms.
- Channel width: 20 MHz.
- Frequency: 5800 MHz.
- Greenfield: disablemisoctl: disable
- Scrambling: disable
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#3: Data transmission
- Switch#100: Management in VLAN 100
| - Type:Slave.
- R5000 Compatibility mode: enableon
- Channel width: 20 MHz.
- Frequency: 5800 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#3: Data transmission
- Switch#100: Management in VLAN 100
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "ОбслуживаниеUpgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: В разделе "Основные настройкиSet the radio parameters values in the section" Basic settings " → "Настройки линка" установите значения параметров RadioLink Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки линка E-ST link settings |
---|
| Image RemovedImage Added |
|
- Step 3: В разделе "Основные настройкиIn the section "Basic settings" → " Коммутатор Switch (MAC Switch) настройте коммутацию согласно требованиям таблицы выше и примените настройки, configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки коммутации E-ST switching settings |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки сети E-ST network settings |
---|
| Image RemovedImage Added |
|
- Step 4: В разделе "Основные настройкиIn the section" Basic settings " → "Статистика линков для интерфейса Link Statistics on rf6.0" проверьте статистику беспроводного соединения. Подробное описание значений параметров представлено в разделе "Состояние устройства", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Статистика беспроводного соединения |
---|
| Image RemovedWireless connection statistics |
| Image Added |
|
Settings via the CLI Настройки R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- Остальные The rest radio parameters and switching settings remain unchanged.
Настройки E-ST settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Настройки радио и коммутацииradio and switching settings |
---|
| rf rf6.0 band 20 transient
rf rf6.0 freq 5800 bitr max sid 10101010
mint rf6.0 -name "E5-STE1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5800 -sid 10101010 -type slave -autobitr -key "456123"
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.27/24
switch group 100 start
switch group 3 add 1 eth0 rf6.0
switch group 3 start |
- Step 3: Проверьте статистику беспроводного соединения командой Check the wireless connection statistics with the command "mint map stat". Выполните тестирование Radioканала командой Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Статистика беспроводного соединенияWireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03270 R5000-Lmn1 00043522CBE6 46/38 130/130 0/0 /TM/
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 8/7 (rx/tx), 15 (sum) Kbps
Total nodes in area: 2 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Сохранение настроекSave settings |
---|
| E5-STE1#1> сo sa |
|
Expand |
---|
title | СценарийScenarios: R5000 - ВедомоеSlave, InfiLINK Evolution - ВедущееMaster |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Параметры устройствSettings parameters |
---|
| configuration R5000-Lmn configuration | configuration E-ST configuration |
---|
Radio | Switching | Radio | Switching |
---|
- Type:Slave.
- Channel width: 40 MHz.
- Frequency: 5500 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#6: Data transmission
- Switch#150: Management in VLAN 150
| - Type: Master.
- R5000 Compatibility mode: enableon
- Frame Size: 5 ms.
- Channel width: 40 MHz.
- Frequency: 5500 MHz.
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#6: Data transmission
- Switch#150: Management in VLAN 150
|
|
|
Settings via the web interface Настройки R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Обслуживание Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- Параметры Radio и настройка коммутации остаются без изменений согласно таблицы выше.
Настройки - The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Обслуживание Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: В разделе "Основные настройкиSet the radio parameters values in the section" Basic settings " → "Настройки линка" установите значения параметров RadioLink Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки линка E-STST link settings |
---|
| Image RemovedImage Added |
|
- Step 3: В разделе "Основные настройкиIn the section "Basic settings" → " Коммутатор Switch (MAC Switch) настройте коммутацию согласно требованиям таблицы выше и примените настройки, configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки коммутации E-ST switching settings |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки сети E-ST network settings |
---|
| Image RemovedImage Added |
|
- Step 4: В разделе "Основные настройкиIn the section" Basic settings " → "Статистика линков для интерфейса Link Statistics on rf6.0" проверьте статистику беспроводного соединения. Подробное описание значений параметров представлено в разделе "Состояние устройства", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Статистика беспроводного соединения |
---|
| Image RemovedWireless connection statistics |
| Image Added |
|
Settings via the CLI Настройки R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
Настройки E-ST settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Настройки радио и коммутацииradio and switching settings |
---|
| rf rf6.0 band 40 transient
rf rf6.0 freq 5500 bitr max sid 10101011
mint rf6.0 -name "E5-STE2"
mint rf6.0 -type master
mint rf6.0 -key "123456"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi150 up
ifc vlan150 vlan 150 vlandev eth0 up
switch group 150 add 2 vlan150 rf6.0
svi 150 group 150
ifc svi100 192.168.98.28/24
switch group 150 start
switch group 6 add 1 eth0 rf6.0
switch group 6 start |
- Step 3: Проверьте статистику беспроводного соединения командой Check the wireless connection statistics with the command "mint map stat". Выполните тестирование Radioканала командой Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Статистика беспроводного соединенияWireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03270 R5000-Lmn1 00043522CBE6 46/38 130/130 0/0 /TM/
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 8/7 (rx/tx), 15 (sum) Kbps
Total nodes in area: 2 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Сохранение настроекSave settings |
---|
| E5-STE1#1> co sa |
|
Топология "точка-многоточка"
Для увеличения пропускной способности сети рекомендуем:
- Заменить сектор базовой станции в соответствии с рекомендациями таблицы в разделе "Соответствие моделей R5000 и Evolution".
- Заменить критически важные абонентские терминалы.
...
Point-to-Multipoint topology
To increase the network throughput, we recommend:
- Replace the base station sector in accordance with the recommendations of the table in the section "R5000 and Evolution models compliance".
- Replace critical subscriber terminals.
Example of upgrading a Point-to-Multipoint network topology
Expand |
---|
title | СценарийScenarios: E-BS - сектор базовой станцииbase station sector; R5000 и and E-ST - абонентские терминалы subscriber terminals |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Параметры устройствSettings parameters |
---|
| configuration E-BS configuration | configuration R5000-Lmn configuration | configuration E-ST configuration |
---|
Radio | Switching | Radio | Switching | Radio | Switching |
---|
- Type: Master.
- R5000 Compatibility mode: enableon
- Frame Size: 5 ms.
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном VLAN 10
- Switch#100: Management in VLAN 100
| - Type:Slave.
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Greenfield: disablemisoctl: disable
- Scrambling: disable
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном in VLAN 10
- Switch#100: Management in VLAN 100
| - Type:Slave.
- R5000 Compatibility mode: enableon
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном in VLAN 10
- Switch#100: Management in VLAN 100
|
|
|
Settings via the web interface Настройки R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Обслуживание Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
Настройки E-BS settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Обслуживание Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: В разделе "Основные настройкиSet the radio parameters values in the section" Basic settings " → "Настройки линка" установите значения параметров RadioLink Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки линка E-BS link settings |
---|
| Image RemovedImage Added |
|
- Step 3: В разделе "Основные настройкиIn the section "Basic settings" → " Коммутатор Switch (MAC Switch) настройте коммутацию согласно требованиям таблицы выше и примените настройки, configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки коммутации E-BS switching settings |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки сети E-BS network settings |
---|
| Image RemovedImage Added |
|
- Step 4: В разделе "Основные настройкиIn the section" Basic settings " → "Статистика линков для интерфейса Link Statistics on rf6.0" проверьте статистику беспроводного соединения. Подробное описание значений параметров представлено в разделе "Состояние устройства", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Статистика беспроводного соединения |
---|
| Image RemovedWireless connection statistics |
| Image Added |
|
Note |
---|
| Perform the E-ST settings analog with E-BS. |
Settings via the CLI Настройки R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
Настройки E-BS settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Настройки радио и коммутацииRadio and switching settings |
---|
| rf rf6.0 band 40 transient
rf rf6.0 freq 5310 bitr max sid 10101010
mint rf6.0 -name "E5-BSE"
mint rf6.0 -type master
mint rf6.0 -key "456123"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.25/24
switch group 100 start
switch group 5 add 1 eth0 rf6.0
switch group 5 vlan 10
switch group 5 start |
- Step 3: Проверьте статистику беспроводного соединения командой Check the wireless connection statistics with the command "mint map stat". Выполните тестирование Radioканала командой Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Статистика беспроводного соединенияWireless connection statistics |
---|
| E5-BSE#1> mint map stat
==============================================================================
Interface rf6.0 TDM (5 ms DL/UL:Auto) (RSSI=-40 Dist=70)
Node 000435252611 "E5-BSE", Id 37425, Nid 0, (Master)
Freq 5310, Band 40, Sid 10101010, autoBitrate 400000/30000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03286 R5000-Lmn 00043522CBF6 47/42 300/300 0/0 /S/
37428 E5-STE2 000435152614 47/48 300/300 0/0 /S/
------- ---------------------------- ------------ ----- ------- ----- -------
2 active neighbors
Total load: 9/11 (rx/tx), 20 (sum) Kbps
Total nodes in area: 3
Links fault 2, Routes fault 0
# Optimal tdma distance 2 km |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Сохранение настроекSave settings |
---|
| E5-BSE#1> co sa |
Note |
---|
| Perform the E-ST settings analog with E-BS. |
|
Expand |
---|
title | Сценарий Scenarios: R5000 - сектор базовой станцииbase station sector, R5000 и and E-ST - абонентские терминалыsubscriber terminals |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| configuration R5000-Mmx configuration | configuration R5000-Lmn configuration | configuration E-ST configuration |
---|
Radio | Switching | Radio | Switching | Radio | Switching |
---|
- Type: Master.
- Frame Size: 5 ms.
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
| - Type: Slave.
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
| - Type:Slave.
- R5000 Compatibility mode: enableon
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 20020
|
|
|
Settings via the web interface Настройки R5000-Mmx, R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Обслуживание Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
Настройки E-ST settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Обслуживание Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: В разделе "Основные настройкиSet the radio parameters values in the section" Basic settings " → "Настройки линка" установите значения параметров RadioLink Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки линка E-ST link settings |
---|
| Image RemovedImage Added |
|
- Step 3: В разделе "Основные настройкиIn the section "Basic settings" → " Коммутатор Switch (MAC Switch) настройте коммутацию согласно требованиям таблицы выше и примените настройки, configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Настройки коммутации E-ST switching settings |
---|
| Image RemovedImage Added |
|
Center |
---|
Scroll Title |
---|
title | Настройки сети E-ST network settings |
---|
| Image RemovedImage Added |
|
- Step 4: В разделе "Основные настройкиIn the section" Basic settings " → "Статистика линков для интерфейса Link Statistics on rf6.0" проверьте статистику беспроводного соединения. Подробное описание значений параметров представлено в разделе "Состояние устройства", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Статистика беспроводного соединения |
---|
| Image RemovedWireless connection statistics |
| Image Added |
|
Settings via the CLI Настройки R5000-Mmx, R5000-Lmn settings - Step 1: Обновите до последней версию ПО с поддержкой технологии TDMA. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfieldmisoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
Настройки E-ST settings - Step 1: Обновите до последней версию ПО. Инструкция по обновлению ПО представлена в разделе "Общие команды Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Настройки радио и коммутацииradio and switching settings |
---|
| rf rf6.0 band 20 transient
rf rf6.0 freq 5100 bitr max sid 10101011
mint rf6.0 -name "E5-STE_Slave1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5100 -sid 10101011 -type slave -autobitr -key "123456"
ifc svi200 up
ifc vlan200 vlan 200 vlandev eth0 up
switch group 200 add 2 vlan200 rf6.0
svi 200 group 200
ifc svi100 192.168.98.25/24
switch group 200 start
switch group 7 add 1 eth0 rf6.0
switch group 7 start |
- Step 3: Проверьте статистику беспроводного соединения командой Check the wireless connection statistics with the command "mint map stat". Выполните тестирование Radioканала командой Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Статистика беспроводного соединенияST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE_Slave1", Id 37429, Nid 0, (Slave)
Freq 5100, Band 20, Sid 10101011, autoBitrate 156000/13000, Noise -103(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
13660 R5000-Mmx 00043514C93C 53/44 130/130 0/0 /TM/F
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 5/0 (rx/tx), 5 (sum) Kbps
Total nodes in area: 3 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BSST: Сохранение настроекSave settings |
---|
| E5-STE1#1> co sa |
|