...
Expand |
---|
title | Scenarios: R5000 - Master, InfiLINK Evolution - Slave |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Lmn сonfiguration | E-ST сonfiguration |
---|
Radio | Switching | Radio | Switching |
---|
- Type: Master.
- Frame Size: 5 ms.
- Channel width: 20 MHz.
- Frequency: 5800 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#3: Data transmission
- Switch#100: Management in VLAN 100
| - Type:Slave.
- R5000 Compatibility mode: enable
- Channel width: 20 MHz.
- Frequency: 5800 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#3: Data transmission
- Switch#100: Management in VLAN 100
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST link settings |
---|
| Image Modified |
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST switching settings |
---|
| Image Modified |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST network settings |
---|
| Image Modified |
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Settings via the CLI R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: radio and switching settings |
---|
| rf rf6.0 band 20 transient
rf rf6.0 freq 5800 bitr max sid 10101010
mint rf6.0 -name "E5-STE1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5800 -sid 10101010 -type slave -autobitr -key "456123"
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.27/24
switch group 100 start
switch group 3 add 1 eth0 rf6.0
switch group 3 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03270 R5000-Lmn1 00043522CBE6 46/38 130/130 0/0 /TM/
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 8/7 (rx/tx), 15 (sum) Kbps
Total nodes in area: 2 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Save settings |
---|
| E5-STE1#1> сo sa |
|
Expand |
---|
title | Scenarios: R5000 - Slave, InfiLINK Evolution - Master |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
| Image Modified |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Lmn configuration | E-ST configuration |
---|
Radio | Switching | Radio | Switching |
---|
- Type:Slave.
- Channel width: 40 MHz.
- Frequency: 5500 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#6: Data transmission
- Switch#150: Management in VLAN 150
| - Type: Master.
- R5000 Compatibility mode: enable
- Frame Size: 5 ms.
- Channel width: 40 MHz.
- Frequency: 5500 MHz.
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#6: Data transmission
- Switch#150: Management in VLAN 150
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The rest radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST link settings |
---|
| Image Modified |
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST switching settings |
---|
| Image Modified |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST network settings |
---|
| Image Modified |
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Settings via the CLI R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: radio and switching settings |
---|
| rf rf6.0 band 40 transient
rf rf6.0 freq 5500 bitr max sid 10101011
mint rf6.0 -name "E5-STE2"
mint rf6.0 -type master
mint rf6.0 -key "123456"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi150 up
ifc vlan150 vlan 150 vlandev eth0 up
switch group 150 add 2 vlan150 rf6.0
svi 150 group 150
ifc svi100 192.168.98.28/24
switch group 150 start
switch group 6 add 1 eth0 rf6.0
switch group 6 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE1", Id 37429, Nid 0, (Slave)
Freq 5800, Band 20, Sid 10101010, autoBitrate 156000/13000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03270 R5000-Lmn1 00043522CBE6 46/38 130/130 0/0 /TM/
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 8/7 (rx/tx), 15 (sum) Kbps
Total nodes in area: 2 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Save settings |
---|
| E5-STE1#1> co sa |
|
...
- Replace the base station sector in accordance with the recommendations of the table in the section "R5000 and Evolution models compliance".
- Replace critical subscriber terminals.
Example of upgrading a Point-to-Multipoint network topology
Expand |
---|
title | Scenarios: E-BS - base station sector; R5000 and E-ST - subscriber terminals |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| E-BS configuration | R5000-Lmn configuration | E-ST configuration |
---|
Radio | Switching | Radio | Switching | Radio | Switching |
---|
- Type: Master.
- R5000 Compatibility mode: enable
- Frame Size: 5 ms.
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном VLAN 10
- Switch#100: Management in VLAN 100
| - Type:Slave.
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном VLAN 10
- Switch#100: Management in VLAN 100
| - Type:Slave.
- R5000 Compatibility mode: enable
- Channel width: 40 MHz.
- Frequency: 5310 MHz.
- Network SID: 10101010.
- Security Key: 456123.
| - Switch#5: Data transmission в выделенном VLAN 10
- Switch#100: Management in VLAN 100
|
|
|
Settings via the web interface R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-BS settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-BS link settings |
---|
| Image Modified |
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-BS switching settings |
---|
| Image Modified |
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-BS network settings |
---|
| Image Modified |
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Note |
---|
| Perform the E-ST settings analog with E-BS. |
Settings via the CLI R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-BS settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Radio and switching settings |
---|
| rf rf6.0 band 40 transient
rf rf6.0 freq 5310 bitr max sid 10101010
mint rf6.0 -name "E5-BSE"
mint rf6.0 -type master
mint rf6.0 -key "456123"
mint rf6.0 -autobitrate
mint rf6.0 -roaming leader
mint rf6.0 tdma mode=Master win=5
ifc svi100 up
ifc vlan100 vlan 100 vlandev eth0 up
switch group 100 add 2 vlan100 rf6.0
svi 100 group 100
ifc svi100 192.168.98.25/24
switch group 100 start
switch group 5 add 1 eth0 rf6.0
switch group 5 vlan 10
switch group 5 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Wireless connection statistics |
---|
| E5-BSE#1> mint map stat
==============================================================================
Interface rf6.0 TDM (5 ms DL/UL:Auto) (RSSI=-40 Dist=70)
Node 000435252611 "E5-BSE", Id 37425, Nid 0, (Master)
Freq 5310, Band 40, Sid 10101010, autoBitrate 400000/30000, Noise -100(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
03286 R5000-Lmn 00043522CBF6 47/42 300/300 0/0 /S/
37428 E5-STE2 000435152614 47/48 300/300 0/0 /S/
------- ---------------------------- ------------ ----- ------- ----- -------
2 active neighbors
Total load: 9/11 (rx/tx), 20 (sum) Kbps
Total nodes in area: 3
Links fault 2, Routes fault 0
# Optimal tdma distance 2 km |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-BS: Save settings |
---|
| E5-BSE#1> co sa |
Note |
---|
| Perform the E-ST settings analog with E-BS. |
|
Expand |
---|
title | Scenarios: R5000 - base station sector, R5000 and E-ST - subscriber terminals |
---|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Connection scheme |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Settings parameters |
---|
| R5000-Mmx configuration | R5000-Lmn configuration | E-ST configuration |
---|
Radio | Switching | Radio | Switching | Radio | Switching |
---|
- Type: Master.
- Frame Size: 5 ms.
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
| - Type: Slave.
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Greenfield: disable
- misoctl: disable
- Scrambling: disable
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
| - Type:Slave.
- R5000 Compatibility mode: enable
- Channel width: 20 MHz.
- Frequency: 5100 MHz.
- Network SID: 10101011.
- Security Key: 123456.
| - Switch#7: Data transmission
- Switch#200: Management in VLAN 200
|
|
|
Settings via the web interface R5000-Mmx, R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "Maintenance menu".
- Step 2: Set the radio parameters values in the section" Basic settings " → "Link Settings".
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST link settings |
---|
|
|
|
- Step 3: In the section "Basic settings" → " Switch (MAC Switch), configure the switching according to the table above requirements and apply the settings.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | E-ST switching settings |
---|
|
|
|
Center |
---|
Scroll Title |
---|
title | E-ST network settings |
---|
|
|
|
- Step 4: In the section" Basic settings " → "Link Statistics on rf6.0", check the wireless connection statistics. A detailed description of the parameter values is provided in the "Device Status" section.
Center |
---|
Scroll Title |
---|
title-alignment | center |
---|
title | Wireless connection statistics |
---|
|
|
|
Settings via the CLI R5000-Mmx, R5000-Lmn settings - Step 1: Upgrade to the latest TDMA firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Check the parameters disabling:
- Greenfield
- misoctl
- Scrambling.
- The radio parameters and switching settings remain unchanged.
E-ST settings - Step 1: Upgrade to the latest firmware version. Procedure are provided in the section "General Purpose Command Set" → "flashnet".
- Step 2: Configure the radio parameters and switching.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: radio and switching settings |
---|
| rf rf6.0 band 20 transient
rf rf6.0 freq 5100 bitr max sid 10101011
mint rf6.0 -name "E5-STE_Slave1"
mint rf6.0 -type slave
mint rf6.0 prof 1 -band 20 -freq 5100 -sid 10101011 -type slave -autobitr -key "123456"
ifc svi200 up
ifc vlan200 vlan 200 vlandev eth0 up
switch group 200 add 2 vlan200 rf6.0
svi 200 group 200
ifc svi100 192.168.98.25/24
switch group 200 start
switch group 7 add 1 eth0 rf6.0
switch group 7 start |
- Step 3: Check the wireless connection statistics with the command "mint map stat". Perform the radio link test with the command "ltest".
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Wireless connection statistics |
---|
| E5-STE1#1> mint map stat
==============================================================================
Interface rf6.0 TDS
Node 000435152615 "E5-STE_Slave1", Id 37429, Nid 0, (Slave)
Freq 5100, Band 20, Sid 10101011, autoBitrate 156000/13000, Noise -103(+0)
------- ---------------------------- ------------ ----- ------- ----- -------
Id Name Node SNR Bitrate Retry Options
------------------------------------ ------------ rx/tx rx/tx rx/tx -------
13660 R5000-Mmx 00043514C93C 53/44 130/130 0/0 /TM/F
------- ---------------------------- ------------ ----- ------- ----- -------
1 active neighbors
Total load: 5/0 (rx/tx), 5 (sum) Kbps
Total nodes in area: 3 |
- Step 4: Save configuration.
Code Block |
---|
language | text |
---|
theme | Emacs |
---|
title | E-ST: Save settings |
---|
| E5-STE1#1> co sa |
|