Include Page | ||||
---|---|---|---|---|
|
Table of Contents |
---|
Предварительная настройка беспроводных устройств
...
Preliminary wireless devices configuration
To perform the alignment, it is necessary to pre-configure the Infinet wireless device, it includes the following steps:
...
Note | ||
---|---|---|
| ||
Процедура юстировки с помощью InfiPOCKET подразумевает его непосредственное сетевое взаимодействие с любым из двух беспроводных устройств. Доступ ко второму будет получен через то устройство, к которому непосредственно подключено мобильное приложение. |
...
| |
The alignment procedure via the InfiPOCKET assume its direct network interaction with any of the two wireless devices. The second will be accessed through the device to which the mobile application is directly connected. |
- Network connection: the device must have the configuration necessary for network connection of a smartphone with InfiPOCKET to a wireless device, according to one of the connection schemes.
- SNMP: SNMP protocol support of any version must be enabled on the device, access credentials must be configured.
- Wireless link: the radio settings must be pre-configured on both devices.
- Additional conditions: follow the instructions for alignment of the corresponding families devices:
Настройка профилей в InfiPOCKET
Для получения данных, необходимых для юстировки, в приложении InfiPOCKET должен быть создан профиль SNMP, который соответствует настройкам SNMP на беспроводном устройстве.
- В главном меню выберите пункт "SNMP-профили". Нажмите кнопку "Создать SNMP-профиль".
- Заполните форму с параметрами профиля SNMP. Значения должны быть идентичны установленным на устройстве, к которому выполняется подключение:
- Произвольное имя профиля.
- Версия SNMP.
- Реквизиты доступа.
- Нажмите кнопку "Сохранить SNMP-профиль".
Center |
---|
Юстировка
Для начала юстировки необходимо подключиться к беспроводному устройству по протоколу SNMP, для этого:
- В разделе "Юстировка" заполните форму подключения:
- IP-адрес беспроводного устройства.
- сетевой порт, используемый для подключения по протоколу SNMP.
- профиль SNMP локального устройства.
- профиль SNMP удалённого устройства, по умолчанию используется профиль, установленный для локального устройства.
- Нажмите кнопку "Подключиться".
- Подтвердите выполнение предварительной настройки беспроводного устройства и перейдите к этапу непосредственной юстировки.
...
Profiles configuration in InfiPOCKET
To obtain the data required for alignment, an SNMP profile must be created in the InfiPOCKET application with SNMP settings match to the wireless device.
- Proceed to the "SNMP Profiles" section of the main menu. Click the "Create SNMP Profile" button.
- Fill in the form with SNMP profile parameters. The values must match the device's settings to which you are connecting:
- Arbitrary profile name.
- SNMP version.
- Access credentials.
- Click the "Save SNMP Profile" button.
Center |
---|
Alignment
To start the alignment, connect to a wireless device via SNMP, using following procedure:
- In the "Alignment" section, fill out the connection form:
- wireless device IP address.
- network port used for SNMP connection.
- SNMP profile of the local device.
- SNMP profile of the remote device, by default the profile set for the local device is used.
- Click the "Connect" buttom.
- Confirm the wireless device was pre-configured and proceed to the alignment step.
Center |
---|